
【国外标准】 Standard Practice for Design and Manufacture of Electric Propulsion Units for Light Sport Aircraft
本网站 发布时间:
2024-02-28
开通会员免费在线看70000余条国内标准,赠送文本下载次数,单本最低仅合13.3元!还可享标准出版进度查询、定制跟踪推送、标准查新等超多特权!  
查看详情>>

适用范围:
3.1 This specification provides designers and manufacturers of electric propulsion for light sport aircraft design references and criteria to use in designing and manufacturing EPUs.3.2 Declaration of compliance is based on testing and documentation during the design, ground testing and flight testing of the EPU by the manufacturer or under the manufacturers’ guidance.3.3 Manufacturers of the EPUs are encouraged to review and incorporate appropriate standards and lessons learned from ground based systems as documented in SAE J2344 and EASA CRI F-58 (see Appendix X2).3.4 Electric aircraft may contain potentially hazardous level of electrical voltage or current. It is important to protect persons from exposure to this hazard. Under normal operating conditions, adequate electrical isolation is achieved through physical separation means such as the use of insulated wire, enclosures, or other barriers to direct contact. There are conditions or events that can occur outside normal operation that can cause this protection to be degraded. Some means should be provided to detect degraded isolation or ground fault. In addition, processes or hardware, or both, should be provided to allow for controlled access to the high voltage system for maintenance or repair. A number of alternative means may be used to achieve these electrical safety goals including automatic hazardous voltage disconnects, manual disconnects, interlock systems, special tools and grounding. The intention of all these means is either to prevent inadvertent contact with hazardous voltages or to prevent damage or injury from the uncontrolled release of electric energy. Lightning strikes are not addressed in this Standard Practice because LSA aircraft are limited to VMC flight only.1.1 This practice covers minimum requirements for the design and manufacture of Electric Propulsion Units (EPU) for light sport aircraft, VFR use. The EPU shall as a minimum consist of the electric motor, associated controllers, disconnects and wiring, an Energy Storage Device (ESD) such as a battery or capacitor, or both, and EPU monitoring gauges and meters. Optional onboard charging devices, in-flight charging devices or other technology may be included.1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
标准号:
ASTM F2840-14(2023)
标准名称:
Standard Practice for Design and Manufacture of Electric Propulsion Units for Light Sport Aircraft
英文名称:
Standard Practice for Design and Manufacture of Electric Propulsion Units for Light Sport Aircraft标准状态:
Active-
发布日期:
-
实施日期:
出版语种:
- 推荐标准
- AS/NZS 61000.4.14:2012 Electromagnetic compatibility (EMC) Testing and measurement techniques - Voltage fluctuation immunity test for equipment with input current not exceeding 16 A per phase
- AS/NZS 61241.14:2005/Amdt 4:2007 Electrical apparatus for use in the presence of combustible dust Selection and installation
- AS/NZS CISPR 14.1:2003 Electromagnetic compatibility - Requirements for household appliances, electric tools and similar apparatus Emission
- AS/NZS CISPR 14.1:2010 Electromagnetic Compatibility - Requirements for household appliances, electrical tools and similar apparatus Emission
- AS/NZS ISO 7176.14:2013 Wheelchairs Power and control systems for electrically powered wheelchairs and scooters - Requirements and test methods
- ASTM 51026-23 Standard Practice for Using the Fricke Dosimetry System
- ASTM 52303-24 Standard Guide for Absorbed-Dose Mapping in Radiation Processing Facilities
- ASTM A1-00(2018) Standard Specification for Carbon Steel Tee Rails
- ASTM A1000/A1000M-17(2023) Standard Specification for Steel Wire, Carbon and Alloy Specialty Spring Quality
- ASTM A1001-18 Standard Specification for High-Strength Steel Castings in Heavy Sections
- ASTM A1002-16(2020) Standard Specification for Castings, Nickel-Aluminum Ordered Alloy
- ASTM A1004/A1004M-99(2018) Standard Practice for Establishing Conformance to the Minimum Expected Corrosion Characteristics of Metallic, Painted-Metallic, and Nonmetallic-Coated Steel Sheet Intended for Use as Cold Formed Framing Members
- ASTM A1009-18 Standard Specification for Soft Magnetic MnZn Ferrite Core Materials for Transformer and Inductor Applications
- ASTM A101-04(2019) Standard Specification for Ferrochromium
- ASTM A1010/A1010M-13(2018) Standard Specification for Higher-Strength Martensitic Stainless Steel Plate, Sheet, and Strip