
【国外标准】 Standard Guide for Installation of Flexible Closed Cell Preformed Insulation in Tube and Sheet Form
本网站 发布时间:
2024-02-28
开通会员免费在线看70000余条国内标准,赠送文本下载次数,单本最低仅合13.3元!还可享标准出版进度查询、定制跟踪推送、标准查新等超多特权!  
查看详情>>

适用范围:
5.1 This guide applies to flexible closed cell insulation tubing and sheet materials manufactured according to Specifications C534 and C1427. This standard is intended to provide a basic guide for installing these types of materials.5.2 Confirm application use temperature is consistent with specified use temperature for material as defined in ASTM Specifications unless otherwise agreed upon with the manufacturer. There are different grades for each of the insulation types referred to in this guide, material and grade installed should be that specified.5.3 This guide is not intended to cover all aspects associated with installation for all applications, consult the National, Commercial Industrial Insulation Standards (MICA Manual) or the specific product manufacturer for recommendations, or both. See ASHRAE Handbook (Fundamentals – Chapter 23) and ASHRAE Handbook (Refrigeration – Chapter 10).1.1 This guide covers recommended installation techniques for flexible closed cell pre-formed insulation in tube or sheet form. This guide is applicable to materials manufactured in accordance with Specification C534 (Elastomeric based insulation) or Specification C1427 (polyolefin based insulation). The materials covered in this guide encompass a service temperature of –297 to 300°F (–183 to 150°C) as indicated in the material specifications referenced above. Many of the recommendations made are specific to below ambient applications only.1.2 The purpose of this guide is to optimize the thermal performance and longevity of installed closed cell flexible insulation systems. By following this guide, the owner, and designer can expect to achieve the energy savings expected and prevention of condensation under the specified design conditions. This document is limited to installation procedures and does not encompass system design.1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
标准号:
ASTM C1710-22
标准名称:
Standard Guide for Installation of Flexible Closed Cell Preformed Insulation in Tube and Sheet Form
英文名称:
Standard Guide for Installation of Flexible Closed Cell Preformed Insulation in Tube and Sheet Form标准状态:
Active-
发布日期:
-
实施日期:
出版语种:
- 推荐标准
- ASTM D6247-18 Standard Test Method for Determination of Elemental Content of Polyolefins by Wavelength Dispersive X-ray Fluorescence Spectrometry
- ASTM D6252/D6252M-98(2019) Standard Test Method for Peel Adhesion of Pressure-Sensitive Label Stocks at a 90° Angle
- ASTM D6254/D6254M-20 Standard Specification for Wirebound Pallet-Type Wood Boxes
- ASTM D6258-17 Standard Test Method for Determination of Solvent Red 164 Dye Concentration in Diesel Fuels
- ASTM D6259-23 Standard Practice for Determination of a Pooled Limit of Quantitation for a Test Method
- ASTM D6261-14(2022) Standard Specification for Extruded and Compression Molded Basic Shapes Made from Thermoplastic Polyester (TPES)
- ASTM D6264/D6264M-23 Standard Test Method for Measuring the Damage Resistance of a Fiber-Reinforced Polymer-Matrix Composite to a Concentrated Quasi-Static Indentation Force
- ASTM D6266-00a(2023) Standard Test Method for Determining the Amount of Volatile Organic Compound (VOC) Released From Waterborne Automotive Coatings and Available for Removal in a VOC Control Device (Abatement)
- ASTM D6267/D6267M-13(2022) Standard Test Method for Apparent Viscosity of Hydrocarbon Resins at Elevated Temperatures
- ASTM D6268-21 Standard Practice for Handling, Transportation, and Storage of HFC-125, Pentafluoroethane (C2HF5)
- ASTM D6270-20 Standard Practice for Use of Scrap Tires in Civil Engineering Applications
- ASTM D6276-19 Standard Test Method for Using pH to Estimate the Soil-Lime Proportion Requirement for Soil Stabilization
- ASTM D6277-07(2022) Standard Test Method for Determination of Benzene in Spark-Ignition Engine Fuels Using Mid Infrared Spectroscopy
- ASTM D6278-20a Standard Test Method for Shear Stability of Polymer Containing Fluids Using a European Diesel Injector Apparatus
- ASTM D6283-21 Standard Test Method for Tuft Element Length of Uncoated Pile Yarn Floor Coverings