
【国外标准】 Standard Test Method for Determination of Cycloparaffin Content in Saturated ATJ-SPK Jet Fuel Gas Chromatography
本网站 发布时间:
2024-02-28
开通会员免费在线看70000余条国内标准,赠送文本下载次数,单本最低仅合13.3元!还可享标准出版进度查询、定制跟踪推送、标准查新等超多特权!  
查看详情>>

适用范围:
5.1 This test method applies specifically to the ATJ-SPK jet fuel as specified in Specification D7566, section A5.4.1, derived from isobutanol and follows the fuel fingerprint described in the annex of this test method. It may not apply to other types of ATJ-SPK fuels.5.2 Table A2.2 in Specification D7566 prescribes cycloparaffin concentration be a maximum of 15 % by mass.5.3 Due to the nature of the chemical composition of ATJ-SPK jet fuel, standard analysis of the sample by Test Method D2425 for cycloparaffin content may yield a higher concentration of cycloparaffins than are actually present in the sample.5.4 This method alleviates the potential for overestimating the cycloparaffin concentration by measuring the concentration of identified paraffins. Any remaining unidentified compounds are classified as potential cycloparaffins.1.1 This test method covers the determination of cycloparaffin content by gas chromatography of the saturated ATJ-SPK jet fuel as specified in Specification D7566, section A5.4.1, derived from isobutanol and follows the fuel fingerprint described in the Annex of this test method.1.2 The working range for the test method is for cycloparaffin content in the range of 1 % to 15 % by mass.1.3 The test method has an interim precision and will be updated once an extended ILS is conducted.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
标准号:
ASTM D8302-20
标准名称:
Standard Test Method for Determination of Cycloparaffin Content in Saturated ATJ-SPK Jet Fuel Gas Chromatography
英文名称:
Standard Test Method for Determination of Cycloparaffin Content in Saturated ATJ-SPK Jet Fuel Gas Chromatography标准状态:
Active-
发布日期:
-
实施日期:
出版语种:
- 其它标准
- 上一篇: ASTM D8301-21 Standard Test Method for Determination of the Content of Nitroxide Radical (4-Hydroxy-2,2,6,6-tetramethylpiperidine-1-oxyl) in Butadiene, Styrene and Isoprene by Cyclic Voltammetry Method
- 下一篇: ASTM D8303-20 Standard Test Method for Determining Thermal Cracking Properties of Asphalt Mixtures Through Measurement of Thermally Induced Stress and Strain
- 推荐标准
- AS/NZS 60695.11.20:2001/Amdt 1:2004 Fire hazard testing Test flames - 500 W flame test methods
- AS/NZS 60745.2.20:2003 Hand-held motor-operated electric tools - Safety - Particular requirements for band saws
- ASTM 51026-23 Standard Practice for Using the Fricke Dosimetry System
- ASTM 52303-24 Standard Guide for Absorbed-Dose Mapping in Radiation Processing Facilities
- ASTM A1-00(2018) Standard Specification for Carbon Steel Tee Rails
- ASTM A1000/A1000M-17(2023) Standard Specification for Steel Wire, Carbon and Alloy Specialty Spring Quality
- ASTM A1001-18 Standard Specification for High-Strength Steel Castings in Heavy Sections
- ASTM A1002-16(2020) Standard Specification for Castings, Nickel-Aluminum Ordered Alloy
- ASTM A1004/A1004M-99(2018) Standard Practice for Establishing Conformance to the Minimum Expected Corrosion Characteristics of Metallic, Painted-Metallic, and Nonmetallic-Coated Steel Sheet Intended for Use as Cold Formed Framing Members
- ASTM A1009-18 Standard Specification for Soft Magnetic MnZn Ferrite Core Materials for Transformer and Inductor Applications
- ASTM A101-04(2019) Standard Specification for Ferrochromium
- ASTM A1010/A1010M-13(2018) Standard Specification for Higher-Strength Martensitic Stainless Steel Plate, Sheet, and Strip
- ASTM A1012-10(2021) Standard Specification for Seamless and Welded Ferritic, Austenitic and Duplex Alloy Steel Condenser and Heat Exchanger Tubes With Integral Fins
- ASTM A1015-01(2018) Standard Guide for Videoborescoping of Tubular Products for Sanitary Applications
- ASTM A1016/A1016M-23 Standard Specification for General Requirements for Ferritic Alloy Steel, Austenitic Alloy Steel, and Stainless Steel Tubes