
【国外标准】 Standard Guide for Emergency Operations Center (EOC) Management
本网站 发布时间:
2024-02-28
开通会员免费在线看70000余条国内标准,赠送文本下载次数,单本最低仅合13.3元!还可享标准出版进度查询、定制跟踪推送、标准查新等超多特权!  
查看详情>>

适用范围:
5.1 Coordination of response and recovery support cannot be performed well if the EOC team lacks an appropriate operating environment. An operating environment that increases stress in staff or hinders the ability to perform basic tasks will ultimately degrade the effectiveness of the EOC team. EOC management must be accomplished in parallel with incident management support and should be transparent to the EOC team. EOC management must also be consistent with and support the incident management system used by the EOC team (for example, the Incident Command System mandated for use in the United States under the National Incident Management System). Effective EOC management can be attributed to good preplanning and related training. This guide provides the emergency management community with practical concepts and approaches for effective EOC management.1.1 This guide provides general guidelines for the management of an emergency operations center (EOC) prior to, during, and after activation for emergency or disaster support.1.2 An EOC is where the coordination of response and recovery support is performed, but the EOC is also a physical location that generates its own demands. For the EOC team to perform effectively, the physical and organizational demands of the EOC as a facility must be met. EOC management is distinct from the operational management of the incident.1.3 This guide may also serve as a foundation for management of a smaller facility such as a department operations center (DOC), larger facilities such as a regional operations center (ROC), or state operations center (SOC) with a broader area of responsibility and more extensive need to communicate and coordinate with others.1.4 This guide applies to fixed facilities and does not specifically address portable or field-deployable EOCs at temporary locations, virtual EOCs using communications technology to link geographically separated participants, or EOC relocation under a Continuity of Operations Plan (COOP). However, elements within this document will apply to these situations.1.5 This guide is the second in a series regarding the EOC. For the Standard Guide for EOC Development, see Guide E2668.1.6 This document includes some references and terminology specific to the United States of America but may be adapted for use elsewhere.1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
标准号:
ASTM E2915-13(2020)
标准名称:
Standard Guide for Emergency Operations Center (EOC) Management
英文名称:
Standard Guide for Emergency Operations Center (EOC) Management标准状态:
Active-
发布日期:
-
实施日期:
出版语种:
- 推荐标准
- ASTM B1-13(2018) Standard Specification for Hard-Drawn Copper Wire
- ASTM B100-20 Standard Specification for Wrought Copper-Alloy Bearing and Expansion Plates and Sheets for Bridge and Other Structural Use
- ASTM B1002-16(2020) Standard Specification for Refined Indium
- ASTM B1003-16(2023) Standard Specification for Seamless Copper Tube for Linesets
- ASTM B1004-16(2022) Standard Practice for Contact Performance Classification of Electrical Connection Systems
- ASTM B1005-17(2023) Standard Specification for Copper-Clad Aluminum Bar for Electrical Purposes (Bus Bar)
- ASTM B1008-18 Standard Test Method for Stress-Strain Testing for Overhead Electrical Conductors
- ASTM B1010/B1010M-19 Standard Specification for Copper-Clad Steel Electrical Conductor for Tracer Wire Applications
- ASTM B1011/B1011M-22 Standard Specification for Cobalt Alloy Spring Wire
- ASTM B1013-22 Standard Specification for High Fluidity (HF) Zinc-Aluminum Alloy Thin Wall Die Castings
- ASTM B1014-20 Standard Specification for Welded Copper and Copper Alloy Condenser and Heat Exchanger Tubes with a Textured Surface(s)
- ASTM B1019-21 Standard Test Method for Determination of Surface Oxides on Copper Rod(for Electrical Purposes)
- ASTM B1020/B1020M-22 Standard Specification for Seamless Nickel Alloy Mechanical Tubing and Hollow Bar
- ASTM B1021-21 Standard Test Method for Peel Resistance of Metal Sheets Joined by High Strength Bonds
- ASTM B1022-22 Standard Specification for Zinc-Aluminum-Magnesium Alloys in Ingot Form for Coating Steel Sheet by the Hot-Dip Process