
【国外标准】 Standard Guide for Monitoring Weather Conditions for Safe Parasail Operation (Withdrawn 2015)
本网站 发布时间:
2024-02-28
- ASTM F2993-13
- Withdrawn, Replaced
- 定价: 0元 / 折扣价: 0 元
- 在线阅读
开通会员免费在线看70000余条国内标准,赠送文本下载次数,单本最低仅合13.3元!还可享标准出版进度查询、定制跟踪推送、标准查新等超多特权!  
查看详情>>

适用范围:
3.1 Every commercial parasail operator shall have a hard mount or handheld visual weather monitoring device. VHF alone is not acceptable.3.2 Each vessel Master shall maintain a weather log in accordance with the procedures in Section 4.3.3 Wind Conditions:3.3.1 Commercial parasailing is prohibited when the current observed wind conditions in the area of operation include a sustained wind speed of more than 20 mph, wind gusts of a difference of 15 mph greater than the sustained wind speed, the wind speed during gusts exceed 25 mph or rain or heavy fog results in reduced visibility of less than 0.5 mile, or when a known lightning storm comes within 7 miles of the parasailing area.3.3.2 Hawaiian Islands region: due to the consistent nature of the offshore trade winds, operators in this region may operate under a 5 mph allowance to the sustained wind speed for offshore wind conditions only. Onshore wind conditions remain the same in accordance with 3.3.1. Therefore, commercial parasailing may occur in sustained offshore wind speeds up to 25 mph.3.4 Sea Conditions—It is understood that sea conditions can cause additional loading of the parasail tow line.3.4.1 Operators in lakes, intercoastal areas, and rivers shall not operate in sea conditions or a wave height that exceed 3 ft. Attention should be given to the specific body of water in these cases as these locations are typically protected areas. Therefore a wave height or water surface condition that meets or exceeds 3-ft waves or chop may be produced by wind that exceeds the 20 mph threshold described in 3.3.3.4.2 Operators in offshore areas shall not operate in sea conditions that exceed a wave height of 4 ft, unless wave height and period are in accordance with the following calculation: 3 s of period for every 1 ft of wave height (for example, 4 ft = 12 s, 5 ft = 15 s, etc.). Wind speed and payload shall also be taken into consideration at all times of operation. The best evidence of wind and wave conditions within the flying area shall be determined by the vessel Master and may differ from a weather service report.3.5 In no case shall parasail operations be conducted in weather conditions that exceed the manufacturer's specified limitations of the equipment being used.1.1 This guide covers monitoring weather conditions for safer parasail operation.1.2 This guide details parasail operators having weather-monitoring devices and keeping a weather log on board their vessels.1.3 Units—The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
标准号:
ASTM F2993-13
标准名称:
Standard Guide for Monitoring Weather Conditions for Safe Parasail Operation (Withdrawn 2015)
英文名称:
Standard Guide for Monitoring Weather Conditions for Safe Parasail Operation (Withdrawn 2015)标准状态:
Withdrawn, Replaced-
发布日期:
-
实施日期:
出版语种:
- 推荐标准
- ASTM D4611-16 Standard Test Method for Specific Heat of Rock and Soil
- ASTM D4614-11(2019) Standard Specification for Ethyl Acetate (All Grades)
- ASTM D4616-23 Standard Test Method for Microscopical Analysis by Reflected Light and Determination of Mesophase in a Pitch
- ASTM D4618-92(2017) Standard Specification for Design and Fabrication of Flue Gas Desulfurization System Components for Protective Lining Application
- ASTM D4619-12(2018) Standard Practice for Inspection of Linings in Operating Flue Gas Desulfurization Systems
- ASTM D4623-16 Standard Test Method for Determination of In Situ Stress in Rock Mass by Overcoring Method—Three Component Borehole Deformation Gauge
- ASTM D4625-21 Standard Test Method for Middle Distillate Fuel Storage Stability at 43 °C (110 °F)
- ASTM D4626-23 Standard Practice for Calculation of Gas Chromatographic Response Factors
- ASTM D4630-19 Standard Test Method for Determining Transmissivity and Storage Coefficient of Low-Permeability Rocks by In Situ Measurements Using the Constant Head Injection Test
- ASTM D4631-18 Standard Test Method for Determining Transmissivity and Storativity of Low Permeability Rocks by In Situ Measurements Using Pressure Pulse Technique
- ASTM D4634-16(2022) Standard Classification System and Basis for Specification for Styrene-Maleic Anhydride Molding and Extrusion Materials (S/MA)
- ASTM D4636-17 Standard Test Method for Corrosiveness and Oxidation Stability of Hydraulic Oils, Aircraft Turbine Engine Lubricants, and Other Highly Refined Oils
- ASTM D4637/D4637M-15(2021)e1 Standard Specification for EPDM Sheet Used in Single-Ply Roof Membrane
- ASTM D4638-16(2023) Standard Guide for Preparation of Biological Samples for Inorganic Chemical Analysis
- ASTM D464-15(2020) Standard Test Methods for Saponification Number of Pine Chemical Products Including Tall Oil and Other Related Products