
【国外标准】 Standard Test Methods for Analysis of Yellow, Orange, and Green Pigments Containing Lead Chromate and Chromium Oxide Green
本网站 发布时间:
2024-02-28
开通会员免费在线看70000余条国内标准,赠送文本下载次数,单本最低仅合13.3元!还可享标准出版进度查询、定制跟踪推送、标准查新等超多特权!  
查看详情>>

适用范围:
4.1 These test methods are for analysis designed as an aid in quality of yellow, orange, and green pigments containing lead chromate and chromium oxide green. Some sections may be applicable to analysis of these pigments when extracted from whole paints.1.1 These test methods cover procedures for the chemical analysis of yellow, orange, and green pigments containing lead chromate and chromium oxide green.1.2 The analytical procedures appear in the following order: SectionsChrome Yellow, Chrome Orange, and Molybdate OrangeOrganic Colors and Lakes 7Moisture and Other Volatile Matter 8Matter Soluble in Water 9Lead Chromate 10 and 11Total Lead 12Sulfate 13 and 14Carbon Dioxide 15Molybdenum 16 and 17Extenders 18 – 22Calculation of Substances Other than Insoluble Lead Compounds 23 and 24Pure Chrome Green and Reduced Chrome GreenOrganic Colors and Lakes 25Moisture and Other Volatile Matter 26Matter Soluble in Water 27Iron Blue 28Lead Chromate 29 and 30Barium Sulfate and Insoluble Siliceous Material 31Total Lead 32Sulfate 33Calcium Oxide Soluble in Acid 34 and 35Extenders 36Calculation of Insoluble Lead Compounds 37Chromium Oxide GreenOrganic Colors and Lakes 38Moisture and Other Volatile Matter 39Matter Soluble in Water 40Total Chromium as Chromium Oxide 411.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.1.4 This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific hazard statements are given in Note 3.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
标准号:
ASTM D126-87(2023)
标准名称:
Standard Test Methods for Analysis of Yellow, Orange, and Green Pigments Containing Lead Chromate and Chromium Oxide Green
英文名称:
Standard Test Methods for Analysis of Yellow, Orange, and Green Pigments Containing Lead Chromate and Chromium Oxide Green标准状态:
Active-
发布日期:
-
实施日期:
出版语种:
- 推荐标准
- ASTM B1-13(2018) Standard Specification for Hard-Drawn Copper Wire
- ASTM B100-20 Standard Specification for Wrought Copper-Alloy Bearing and Expansion Plates and Sheets for Bridge and Other Structural Use
- ASTM B1002-16(2020) Standard Specification for Refined Indium
- ASTM B1003-16(2023) Standard Specification for Seamless Copper Tube for Linesets
- ASTM B1004-16(2022) Standard Practice for Contact Performance Classification of Electrical Connection Systems
- ASTM B1005-17(2023) Standard Specification for Copper-Clad Aluminum Bar for Electrical Purposes (Bus Bar)
- ASTM B1008-18 Standard Test Method for Stress-Strain Testing for Overhead Electrical Conductors
- ASTM B1010/B1010M-19 Standard Specification for Copper-Clad Steel Electrical Conductor for Tracer Wire Applications
- ASTM B1011/B1011M-22 Standard Specification for Cobalt Alloy Spring Wire
- ASTM B1013-22 Standard Specification for High Fluidity (HF) Zinc-Aluminum Alloy Thin Wall Die Castings
- ASTM B1014-20 Standard Specification for Welded Copper and Copper Alloy Condenser and Heat Exchanger Tubes with a Textured Surface(s)
- ASTM B1019-21 Standard Test Method for Determination of Surface Oxides on Copper Rod(for Electrical Purposes)
- ASTM B1020/B1020M-22 Standard Specification for Seamless Nickel Alloy Mechanical Tubing and Hollow Bar
- ASTM B1021-21 Standard Test Method for Peel Resistance of Metal Sheets Joined by High Strength Bonds
- ASTM B1022-22 Standard Specification for Zinc-Aluminum-Magnesium Alloys in Ingot Form for Coating Steel Sheet by the Hot-Dip Process