【国外标准】 Standard Practice for Evaluating Compatibility of Mixtures of Turbine Lubricating Oils

5.1 The compatibility of oils can be important for users of oil-lubricated equipment. Mixing of two oils can produce a substance markedly inferior to either of its constituent materials. One or more of the following can occur:5.1.1 A mixture of incompatible oils most often forms a precipitate. The precipitate will form unwanted deposits in the lubrication system, plug filters, and oil passageways.5.1.2 A mixture of incompatible oils will sometimes exhibit degradation of certain performance parameters like demulsibility, foam inhibition oxidation stability, rust protection ability, or antiwear protection ability.5.1.3 A mixture of incompatible oils will sometimes exhibit non-miscibility of the base oils with each other.5.1.4 Such incompatibilities can lead to catastrophic equipment failures.5.2 To minimize the chances of these problems occurring, lubricant suppliers recommend evaluating compatibility of lubricating oil of different formulations and sources prior to mixing. Equipment users most often do not have the resources to evaluate oil compatibility and must rely on their suppliers. Mixing of oils without first determining the compatibility is a highly imprudent practice.5.3 Although new turbine oils may be compatible, in-service oil of the same type may be degraded or contaminated to such an extent that the new oil added may not be compatible with the system oil. In-service oil compatibility with new oil additions should be evaluated on a case-by-case basis.5.4 The oxidation resistance of different oils of the same type can vary widely, and compatibility does not imply equivalent performance without oxidation performance testing.1.1 This practice covers the compatibility of mixtures of turbine lubricating oils as defined by Specification D4304. The methods compare properties of specific mixtures with those of the neat oils after storage at specified conditions.1.2 The methods are grouped into four tiers of testing types:1.2.1 Tier 1—Visual appearance1.2.2 Tier 2—Interfacial properties1.2.3 Tier 3—Physical and chemical properties1.2.4 Tier 4—Specific performance properties1.3 The methods can be used to evaluate new (unused) lubricant compatibility or the effects of adding new (unused) lubricant to in-service lubricant in the system.1.4 This practice does not evaluate the wear prevention characteristics, load carrying capacity, or the mechanical shear stability of lubricants mixtures while in service. If anti-wear (AW), extreme pressure (EP), or shear stability are to be evaluated, further testing of these parameters may be required.1.5 Mixtures of the two constituent oils are evaluated using the Tier 1 and Tier 2 testing protocol. Sequential or concurrent testing is continued by applying tests from Tier 3 or Tier 4 until the test requestor or user is satisfied that the intent of this practice has been met. If any mixture fails the methods, the oils are considered incompatible by that method. If all mixtures pass the methods, the oils are considered compatible by those methods. It is recommended that passing only Tier 1 does not adequately test for fluid compatibility.1.6 If the mixture passes Tier 1, it shows two oils are visually compatible only. If the mixture passes Tier 1 and 2, it shows two oils are visually and interfacially compatible. If the mixture passes Tier 1, 2 and 3, it shows two oils are visually, interfacially, physically, and chemically compatible. If the mixture passes Tier 1, 2, 3, 4, it shows two oils are compatible with the highest confidence level. Testing each tier level is giving the user more confidence that the two fluids are compatible.1.7 This practice applies only to lubricating oils having characteristics suitable for evaluation by the suggested test methods. If the scope of a specific test method limits testing to those oils within a specified range of properties, oils outside that range cannot be tested for compatibility by that test method.1.8 This practice may be used to evaluate the compatibility of different types and grades of oil. However, it is not intended to evaluate such mixtures for lubrication performance. The user is advised to consult with suppliers in these situations.1.9 This practice does not purport to cover all test methods that could be employed.1.10 The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard.1.11 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.12 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.