
【国外标准】 Standard Test Method for Evaluating the Adhesion (Pull-Off) Strength of Concrete Repair and Overlay Mortar
本网站 发布时间:
2024-02-28
开通会员免费在线看70000余条国内标准,赠送文本下载次数,单本最低仅合13.3元!还可享标准出版进度查询、定制跟踪推送、标准查新等超多特权!  
查看详情>>

适用范围:
5.1 When the test is performed on the repair or overlay material, the result is the bond strength to the concrete panel or the tensile strength of either the overlay or concrete panel, whichever is weaker.5.2 The measured strength is controlled by the failure mechanism requiring the least stress. Thus, it is not possible to know beforehand which strength will be measured by the test. For this reason, the failure mode has to be reported for each individual test result, and tests results are averaged only if the same failure mode occurs. Alternatively, one can infer that the bond strength is greater than the failure stress if the bond does not fail during the test.5.3 The method may also be used to evaluate the performance of bonding agents.5.4 This test method is designed to evaluate bond strengths in the laboratory and to standardize conditions that permit comparison of results between laboratories. It is not intended to determine bond strength for field applications as results obtained are only applicable to the standard substrate.1.1 This test method is suitable for laboratory use to determine one or more of the following:1.1.1 The bond strength of a repair or an overlay material to a specific concrete substrate.1.1.2 The tensile strength of a repair or overlay material after the material has been applied to the concrete substrate.1.1.3 The change in bond strength when applying a bonding agent or other bond modifying treatment to the concrete substrate.1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined. Some values have only SI units because the inch-pound equivalents are not used in practice.1.2.1 If required results obtained from another standard are not reported in the same system of units as used by this test method, it is permitted to convert those results using the conversion factors found in the SI Quick Reference Guide.21.3 The text of this test method refers to notes and footnotes that provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of this test method.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. (Warning—Fresh hydraulic cementitious mixtures are caustic and may cause chemical burns to skin and tissue upon prolonged exposure.)31.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
标准号:
ASTM C1857/C1857M-19
标准名称:
Standard Test Method for Evaluating the Adhesion (Pull-Off) Strength of Concrete Repair and Overlay Mortar
英文名称:
Standard Test Method for Evaluating the Adhesion (Pull-Off) Strength of Concrete Repair and Overlay Mortar标准状态:
Active-
发布日期:
-
实施日期:
出版语种:
- 其它标准
- 上一篇: ASTM C1856/C1856M-17 Standard Practice for Fabricating and Testing Specimens of Ultra-High Performance Concrete
- 下一篇: ASTM C1858-17a(2021) Standard Practice for Design, Construction, and Material Requirements for Direct Hung Suspended T-bar Type Ceiling Systems Intended to Receive Gypsum Panel Products in Areas Subject to Earthquake Ground Motions
- 推荐标准
- INCITS 93M-1981 (S2017) Optical Character Recognition Positioning
- INCITS/ISO/IEC 14496-19:2004 (R2019) Information technology - Coding of audio-visual objects - Part 19: Synthesized texture stream
- INCITS/ISO/IEC 23000-19:2020 (2021) Information technology - Multimedia application format (MPEG-A) - Part 19: Common media application format (CMAF) for segmented media
- ASTM D8137-18(2023) Practice for Accelerated Aging of Leather
- ASTM D8138-23 Standard Specification for Preformed Silicone Joint Sealing System for Bridges
- ASTM D8139-23 Standard Specification for Semi-Rigid, Closed-Cell Polypropylene Foam, Preformed Expansion Joint Fillers for Concrete Paving and Structural Construction
- ASTM D814-95(2020) Standard Test Method for Rubber Property—Vapor Transmission of Volatile Liquids
- ASTM D8140-18(2023) Standard Guide for the Use of Foundry Sand in Asphalt Mixtures
- ASTM D8141-22 Standard Guide for Selecting Volatile Organic Compounds (VOCs) and Semi-Volatile Organic Compounds (SVOCs) Emission Testing Methods to Determine Emission Parameters for Modeling of Indoor Environments
- ASTM D8144-22 Standard Test Method for Separation and Determination of Aromatics, Nonaromatics, and FAME Fractions in Middle Distillates by Solid-Phase Extraction and Gas Chromatography
- ASTM D8148-22 Standard Test Method for Spectroscopic Determination of Haze in Fuels
- ASTM D8149-20 Standard Practice for Optimization, Calibration, and Validation of Ion Chromatographic Determination of Heteroatoms and Anions in Petroleum Products and Lubricants
- ASTM D8150-22 Standard Test Method for Determination of Organic Chloride Content in Crude Oil by Distillation Followed by Detection Using Combustion Ion Chromatography
- ASTM D8152-18 Standard Practice for Measuring Field Infiltration Rate and Calculating Field Hydraulic Conductivity Using the Modified Philip Dunne Infiltrometer Test
- ASTM D8154-24 Standard Test Methods for 1H-NMR Determination of Ketone-Ethylene-Ester and Polyvinyl Chloride Contents in KEE-PVC Roofing Fabrics